Government Facility Network Installation Service

The Network Installers designs and installs network cabling and WiFi for federal, state, and local government agencies, with procurement available through CMAS, GSA Schedule 84, PEPPM, BuyBoard, and Sourcewell.

Get A Free Quote

🔒︎ Your information will be kept Private

19+

Years Experience

20k+

Locations Protected

99%

Satisfaction Rating

Government Network Cabling and WiFi

The Network Installers builds the cabling, WiFi, and low-voltage infrastructure inside federal, state, and local government facilities. Federal institutions handle confidential data and operate under strict mandates: NDAA Section 889 restricts which manufacturers can supply networking equipment, the Trade Agreements Act governs country of origin, and FISMA defines the security controls federal systems must meet. We specify NDAA-compliant switches, access points, and cameras and document every install for audit. To protect data and critical infrastructure, we install structured copper (Cat 5e, Cat 6, Cat 6A) and fiber optic cabling for government facilities, terminated and tested by BICSI-trained technicians under California C7 Low Voltage License #1039579. Our cabling work follows ANSI/TIA-568 standards and ships labeled patch panels, certification test reports, and as-built drawings. We install enterprise WiFi on Cisco Meraki, Aruba, and Ruckus platforms. We also install low-voltage cabling that supports access control, IP cameras, and intercoms on the same pull. If you are scoping a government project, contact us today. We also repair and upgrade existing networks.

Site Assessment

A government site survey delivers a cable pathway map, a compliance baseline (NDAA, TAA, ANSI/TIA-568), and an equipment inventory before any cable is pulled. BICSI-trained surveyors at The Network Installers review and document your network and hand off a scoped install package.

Engineer

Our engineers design the network topology, structured cabling layout, wireless access point placement, and conduit routing for your government facility install. Designs follow ANSI/TIA-568 standards and specify NDAA-compliant switches, access points, and cameras throughout the project.

Install

Install includes cable pulls, terminations, certification testing, and labeled run reports for every drop. After site assessment and engineering, we run cable in your government facility on schedule and hand over an audit-ready documentation package.

The Network Installers is the top-rated Data Cabling Company for Government Facilities

The Network Installers has installed network cabling for City of Emeryville and other public agencies, with procurement available through CMAS, GSA Schedule 84, PEPPM, BuyBoard, and Sourcewell. Reviews from agencies and businesses we have worked with appear below.

The Network Installers

Telecommunications service provider

Network Installers were fabulous to work with. Larry came out to our office to inspect and quote the project. They came out as scheduled and did the work. Great quality work and easy to have them in our office. I would highly recommend Larry and The network Installers!

On behalf of Regency Centers, I was tremendously grateful for the support The Network Installers were able to provide during my recent office move. Larry Wertz assisted me, along with my offsite IT Team, as we navigated a couple of unforeseen challenges. His team of Technicians were knowledgeable and dependable, assisting us to achieve all our deadlines. Many thanks! Kurstin Montero

This group was great. Everyone that I talked to was friendly, helpful, and knew what they were doing. I was having issues for my small business's IT systems, and they were quick to come out and get it fixed. If I have any issues, I will absolutely reach out to them again, and I highly recommend them to anyone looking for IT support.

Government Facility Data Cabling

Government facility data cabling runs on Cat 5e for voice, Cat 6 for gigabit data, and Cat 6A for 10G backbones. Government facilities have stricter rules than the private sector, so we follow ANSI/TIA-568 standards and specify NDAA-compliant switches and access points. Every drop is terminated and tested by Belden- and Panduit-certified installers, with labeled patch panels and an audit-ready test report at handoff.

Wifi for Government Facilities

WiFi for government facilities runs on enterprise platforms (Cisco Meraki, Aruba, Ruckus) with secure SSID segmentation for staff, guest, IoT, and public-facing networks. Reliable wireless is non-negotiable for agencies running VoIP, body-camera uploads, badge readers, or visitor check-in. The Network Installers installs WiFi for government facilities with WPA3-Enterprise authentication, AP heat-mapping site surveys, and centralized management.

Fiber Optic Cabling for Government Facility

OS2 single-mode fiber connects buildings across a government campus and scales from 1G to 100G by swapping the optics on each end, no recabling required. The Network Installers also installs OM4 multimode fiber for in-building backbones and short data center runs. Our fusion-spliced terminations are OTDR-tested and documented per run. Connect with us for a fiber plant your facility can grow into for the next 20 years.

Locations

The Network Installers is headquartered in California with crews dispatched nationwide for multi-site government work. With the trust of agencies at the city, county, state, and federal level, we have extended our installation services for our customers at the locations below.

Government Facility Cabling Solutions

The Network Installers covers the full government facility cabling lifecycle: site survey, cable design, NDAA-compliant equipment spec, install, certification testing, and audit-ready documentation handover. Every drop is labeled, every patch panel is mapped, and every termination is BICSI-compliant. Our installers deliver structured copper, OS2 single-mode fiber, OM4 multimode fiber, and the supporting cable management you need, scoped to your facility size.

Wireless Network Design for Government Facilities

Wireless network design for a government facility starts with a site survey and AP heat-map that document coverage gaps before any AP is mounted. Secure SSID segmentation, RADIUS authentication, and integration with the wired structured cabling backbone determine whether the WiFi performs at handoff. The Network Installers delivers wireless design that holds up under real agency workloads.

Brands We Install

The Network Installers installs network cabling for government facilities using Cisco Meraki, Aruba, Ruckus, Ubiquiti, Belden, Panduit, and Extreme Networks equipment. We are brand-agnostic and recommend the platform that fits your facility, security policy, and budget. Contact us today!

Frequently Asked Questions

What compliance frameworks does network cabling for a government facility need to meet?

Government network installation typically has to satisfy four overlapping frameworks. NDAA Section 889 bans equipment from five named manufacturers on any government-funded project. The Trade Agreements Act governs country of origin for products purchased through GSA Schedules. FISMA defines the security controls federal information systems must implement. CJIS applies to any agency that touches FBI databases or criminal records. The Network Installers specifies NDAA-compliant switches, access points, and cameras and documents every install so your facility passes audit.

Which procurement vehicles can government agencies use to purchase network installation through The Network Installers?

We are reachable through CMAS, GSA Schedule 84, PEPPM, BuyBoard, OMNIA Partners, Sourcewell, DIR, SAM.gov, and E&I Cooperative. Procurement officers at federal, state, and local agencies can use whichever cooperative or schedule already covers their purchasing process, so a network upgrade does not have to wait for a separate competitive bid.

Can The Network Installers work in classified or sensitive government facilities?

We install commercial network cabling and wireless infrastructure for government facilities at the unclassified level and in sensitive but unclassified environments. For projects that require background-checked technicians, secure pathway design, or specific physical-security protocols, we scope those requirements into the project plan and document the controls in the install package. Send us your facility profile and we will scope what we can and cannot deliver under your security policy.

What is the difference between NDAA-compliant and TAA-compliant networking equipment?

NDAA Section 889 bans equipment from a specific list of manufacturers (currently Hikvision, Dahua, Hytera, Huawei, and ZTE) on government-funded projects. TAA requires that products be made in the United States or substantially transformed in a designated country. NDAA-compliant equipment is not automatically TAA-compliant, and many GSA Schedule purchases require both. We specify equipment that meets the framework your purchasing vehicle requires.

Does The Network Installers serve federal, state, and local government agencies?

Yes. We work with federal agencies, state departments, county governments, municipal buildings, transit agencies, water districts, and public-safety facilities. We are headquartered in California and dispatch crews nationwide for multi-site government work, with consistent install standards at every facility.